Best ecu flash for zx10r
- #BEST ECU FLASH FOR ZX10R INSTALL#
- #BEST ECU FLASH FOR ZX10R FULL#
- #BEST ECU FLASH FOR ZX10R SOFTWARE#
The Kawasaki Pit Speed Limiter harness plugs into the bike's Exhaust Valve Plug and allows the rider to enable the Pit Speed Limiter and, where available, the Engine Warm Up feature. Kawasaki Pit Speed Limiter Harness Type 1 This product includes the Kawasaki Pit Speed Limiter Harness Type 1 and Pit Speed Limiter Key allowing you to enable the Pit Speed Limiter in 1 ECU within the Woolich Racing Tuned (WRT) software. If you have purchased the Race Tools package you do not need to purchase this key.Ģ016-2018 Kawasaki ZX10R Pit Speed Limiter Launch Control is part of the Race Tools package. Purchase this item to allow you to enable the Woolich Racing Launch Control.
![best ecu flash for zx10r best ecu flash for zx10r](https://www.cyclegear.com/_a/product_images/0171/9806/graves_motorsports2016_kawasaki_zx10_r_cat_eliminator_titanium_exhaust_system_carbon_fiber_carbon_fiber_750x750.jpg)
** The Pit Speed Limiter and Engine Warm Up, requires the purchase of an additional Pit Speed Limiter Harness.Ģ016-2020 Kawasaki ZX10R Launch Control Key
![best ecu flash for zx10r best ecu flash for zx10r](https://cdn.shopify.com/s/files/1/0666/2265/products/woolich-racing-kawasaki-extension-harness-type-13a_1024x1024.jpg)
#BEST ECU FLASH FOR ZX10R SOFTWARE#
** This harness uses the stock exhaust valve plugs on the bike's harness, the stock exhaust valve should be removed from the bike and disabled in the WRT software This item is for the Race Tools Key Only, it allows you to enable Woolich Racing Race Tools using the stock Shift Sensor.
#BEST ECU FLASH FOR ZX10R INSTALL#
If you do not have a Woolich Racing Interface you can also visit a Woolich Racing - Tuning Partner and have them install and configure the Race Tools (additional fees and charges will apply). You can purchase this as a package on the product page for your bike. You will need to use the relevant Woolich Racing Interface and Bin File Definition to enable and configure Race Tools and write to the ECU. Woolich Racing Race Tools requires you to Write the ECU. ** The Pit Speed Limiter and Engine Warm Up requires the purchase of an additional Pit Speed Limiter Harness. * Contact us after ordering if you have after-market rearsets or are using a race shift pattern and we will swap the shift rod for a generic rod that can be cut and tapped to the correct length. Launch Control allows you to configure Delay, Launch RPM and Hold Speed.Įngine Warm up parameters are fully configurable. Pit Speed Limiter RPM can be configured.**
#BEST ECU FLASH FOR ZX10R FULL#
Quickshifter Kill times are configurable per gear with 3D maps allowing Kill Times to be set for the full range of TPS and RPM combinations.Īutoblipper Opening and Target maps are fully configurable per gear.
![best ecu flash for zx10r best ecu flash for zx10r](https://www.veloxracing.com/wp-content/uploads/2021/11/Stringer-Stacks-ZX10R-2016-Dyno.jpeg)
Kawasaki Race Tools Type 5 which allows the quickshifter to be plugged into the bikes wiring harness**.Shift rod for standard shift configuration*.High quality dual direction strain gauge Quickshifter with digitally controlled pressure sensing that can be used in regular or race shift pattern.The Race Tools package allows you to add Autoblipper, Quickshifter, Pit Speed Limiter, Engine Warm Up and Launch Control to the Stock ECU. Race Tools: Quickshifter, Launch Control, Pit Speed Limiter